HZS SERIES
The “HZS” is ideal for use in piercing, riveting, notching, clamping, marking, coining, and assembly applications where short-stroke, high speed, high force operation is desirable. This unit is ideal for situations where a low profile is required and is ideal when replacing short stroke Hydraulic cylinders without the mess, noise and maintenance of comparable Hydraulic counterparts.
- Multiple mounting configurations
- Multiple work sections to 1 booster available
- Most options available for PS only series
- Wide selection on power strokes
- Special rod ends
- AVAILABILITY: 4-6 WEEKS STANDARD, EXPEDITE AVAILABLE
(CALL FOR SPECIFIC AVAILABILITY) - MODEL: HZS-XX-X.XX-X.XX-FH-XXXX
- Power Strokes up to 4.00” [50mm] using 0.25” increments for HZS, and up to 1.50” Power Stroke for HZ
- Perfect for Stamping, coining, marking, high-speed punching where strokes are short and force is high
- 670 lbs. – 40,000 lbs. [2.9kN – 177.9kN] using up to 100 PSI [6.9 bar] shop air.
- Add the IntelliCylTM option for Force & Distance monitoring
- Other options – Non-Rotate, Pneumatic Port positions 1-4, Rod Extensions, Rod thread pattern (male or female), ELT auto power stroke sensor, BSPP or “G” pneumatic porting (not available on 1-Ton & 2-Ton units), Pressure Switches, Remote Pressure Block (PB-1), NFPA mounting available on request.
| Sell Sheet: | HZS Sell Sheet |
|---|---|
| Hose-Fitting Specs: | Hydraulic Fittings and Hose |
| Fill and Vent Procedures: | 2-Position Spring Return 3-Position Open Center |
| Cylinder Component and Seal Callout: | Cylinder Seal Replacement Instructions |
| Approved Pneumatic Schematics: | HZS Series Pneumatic Schematic |
| Troubleshooting: | Troubleshooting Guide Serial Number Location |
RELATED OPTIONS
(LTI) EXTERNAL LINEAR TRANSDUCER
Low Voltage Linear Transducers –VIEW
Magnetostrictive technology with Auto Tuning, non-contact, wear free, Analog, Digital, SSI, Pulse, CANopen, Profibus and Quadrature output, .0001″ resolution capable, 7-pin connector/cable. NOTE: Non-Rotate option required for addition of LTI.
-Resolution: 0.66A
-Non-linearity: +/- 0.02% over full scale
-Repeat-ability Resolution: min 2m
-Sampling Rate 2KHz
-Operating Voltage 24Vdc or 15Vdc
(LT) INTERNAL LINEAR TRANSDUCER
Integrally Mounted Low Voltage Linear Transducers –VIEW Magnetostrictive technology with Auto Tuning, non-contact, wear free, Analog, Digital, .0001″ resolution capable, 7-pin connector/cable.
-Resolution: 0.66A
-Non-linearity: +/- 0.02% over full scale
-Repeat-ability Resolution: min 2m
-Sampling Rate 2KHz
-Operating Voltage 24Vdc or 15Vdc
(LC) LOAD CELL
Strain bridge design load cell. Load cell O.D. matches drive unit ram O.D. for a compact, integrated design. Mini Brad-Harrison style four 4-pin connector. Signal conditioner is required.
-Rated Output: 2mV/ V
-Combined Error: 0.25% of full scale
-Non-repeatability: 0.05%
-Zero Balance: 1%
-Excitation Voltage: 10VDC
-Maximum Load: 200% of full -scale (ultimate) / 150% of full scale (safe)
(BSPP) PNEUMATIC PORTING
Pneumatic porting available to order in BSPP porting. All pneumatic ports (4).
Porting of “NPT” is standard.
(AL) MECHANICAL ROD LOCK
The “AL” Rod Lock option is a locking device installed on the head end of the cylinder that provides a positive locking of the cylinder rod when air is removed from the lock. The locking action is designed where safety considerations require positive locking of the tooling/actuator when air pressure is removed from the circuit. The rod lock option is available for all 1 through 30 ton HyperCyl® cylinders. Rod Lock – 60 PSI minimum air pressure required.
(TSL) TOTAL STROKE LIMITER
The “TSL” option limits the total stroke of the cylinder, including the power stroke. Adjustment is accomplished by rotating the adjustment barrel and locking ring.
(NR) NON-ROTATE
Utilizing the flats on the external work rod, the Non-Rotate option provides a mechanical non-rotate rod/adapter plate for Anti-rotate.
Included: NR plate, NR rod, NR/FH head and fasteners.
(S) NON-STANDARD ROD END
The cylinder rod end can be modified to adapt to customer tooling, die plates and/or just about anything else that is required. Please make your request known during the quoting process.
Standard– Female, imperial thread.
SPECIAL MOUNTING
Please contact our sales team at 734-529-8855 for more information.
ACCESSORIES
(SWD) HEAVY DUTY DIGITAL PRESSURE SWITCH
(SW) HEAVY DUTY ANALOG PRESSURE SWITCH
(G-01) HYDRAULIC GAGE KITS
(PHA-XX) HIGH PRESSURE HOSE ASSEMBLIES
(PB) PRESSURE BLOCK
(IC-1) PRESSURE COUPLING
(GA-1) GAGE ADAPTER COUPLING
(HFP-1) PNEUMATIC FILL UNIT
(HFP-2) MANUAL FILL UNIT
(PT)(ELT) SENSORS
(SIG) HYPERVIEW PRESS MONITORING SYSTEM
(PAF-XX) DIE SET MIS-ALIGNMENT COUPLINGS
(PAQ-XX) QUICK CHANGE DIE SET MIS-ALIGNMENT COUPLINGS
(NGT) PILOT OPERATED CHECK VALVE
(FC) PNEUMATIC FLOW CONTROL